# Hot tire pickup: what a fix costs

> What it costs to fix hot tire pickup: spot repair, full recoat and grind-and-rebuild prices on a 400 square foot garage, with the arithmetic shown.

Canonical: https://epoxygaragefloorlab.com/hot-tire-pickup-cost/

Last updated: 2026-11-09

Hot tire pickup repair costs $50 to $250 in materials for an isolated mark, $2,000 to $4,800 to recoat a 400 square foot garage at $5 to $12 per square foot, or $2,800 to $6,000 to grind the old system off and rebuild. The deciding variable is not the size of the marks but whether the base coat underneath is still bonded.

## What the repair is actually priced on

A hot tire mark is a missing patch of coating, not a stain. The repair has to replace the film, which means cleaning, profiling, priming, and recoating. The price follows the area and the depth of the failure.

Three outcomes are possible. If the base is sound and the marks are few, the repair is local. If the base is sound and the marks are widespread, the whole topcoat is suspect and a recoat is the sensible fix. If the base is hollow or lifting, the system has to come off.

Each outcome has a different cost structure, and a quote that does not distinguish them is not a real estimate.

## Cost by repair level

| Repair | Area | Rate | Total |
| :--- | :--- | :--- | :--- |
| Spot repair, DIY | 10 sq ft | $5 / sq ft material | $50 |
| Spot repair, professional | 10 sq ft | Minimum call | $150 - $400 |
| Full recoat, low end | 400 sq ft | $5 / sq ft | $2,000 |
| Full recoat, high end | 400 sq ft | $12 / sq ft | $4,800 |
| Grind and rebuild, low | 400 sq ft | $5 + $1 / sq ft | $2,400 |
| Grind and rebuild, high | 400 sq ft | $12 + $3 / sq ft | $6,000 |

The recoat figures assume the base is sound and no moisture mitigation is needed. Add mitigation at $2 to $5 per square foot if the slab tests high.

## The arithmetic on a 400 square foot garage

Start with the recoat. At $7 per square foot, 400 × $7 = $2,800. At $10, 400 × $10 = $4,000. That covers scuffing, cleaning, and one or two topcoat passes.

Now the rebuild. Grinding at $2 per square foot is 400 × $2 = $800. A new base and topcoat at $8 is 400 × $8 = $3,200. The subtotal is $4,000. Add three crack repairs at $75, or $225, and the total is $4,225.

With moisture mitigation at $3.50 per square foot, 400 × $3.50 = $1,400, the rebuild reaches $5,625. That is the realistic worst case for a slab with no vapor barrier.

Compare the recoat at $2,800 with the rebuild at $4,225. The recoat saves $1,425, and it is the right choice when the base is bonded.

## What drives the price up

Access is the first factor. A garage with a clear driveway and 8 foot ceilings is straightforward. A basement garage or a tight urban bay where equipment has to be carried in adds labor that a per-square-foot rate does not capture.

Floor condition is the second. A floor with one type of coating lifts cleanly under a grinder. A floor with patches of different products, or a previous DIY coat over a sealer, takes more passes and more tooling.

Topcoat choice is the third. A standard epoxy clear sits at the low end of the recoat range. An aliphatic polyurethane or polyaspartic sits at the high end, and it is the specification that resists hot tire pickup in the first place.

## What the cheap fix costs later

A $150 spot repair over a contaminated surface will lift again. A $300 recoat without scuffing will peel in sheets. A rebuild without a moisture test will blister.

The pattern is that the second repair costs more than the first one done correctly. Grinding off a failed recoat is the same $800 as grinding off the original, and then the new system is another $3,200. A $2,800 recoat that fails becomes a $4,800 job.

There is also a timing cost. A failed recoat usually shows itself in the first heating season, which means the floor is out of service twice and the garage is emptied twice. That inconvenience rarely appears in a quote but it is real, and it is the reason a correct diagnosis is worth more than a cheap first attempt.

That is the argument for diagnosing before pricing. Tap the floor, check the moisture, and confirm whether the base is bonded. The diagnosis costs nothing and decides which of the three repair levels is appropriate.

## Getting a quote that can be compared

1. Ask for the measured square footage, not an estimate from a listing.
2. Ask whether the quote assumes the base is sound, and how that was verified.
3. Confirm whether grinding is included and at what rate per square foot.
4. Confirm the topcoat chemistry and the number of coats.
5. Ask for the moisture test result if mitigation is not included.
6. Check the cure time stated for vehicle traffic.

Two quotes that differ by $2,000 are usually not competing on price. One includes grinding and a urethane topcoat, the other applies a coat over the existing film.

For the repair methods behind these numbers, read [hot tire pickup repair options](https://epoxygaragefloorlab.com/hot-tire-pickup-repair/). For the system specification that avoids the problem, see [polyurethane vs epoxy](https://epoxygaragefloorlab.com/polyurethane-vs-epoxy/). And for the wider cost picture on a new floor, check the [epoxy garage floor cost guide](https://epoxygaragefloorlab.com/epoxy-garage-floor-cost-per-square-foot/).