# Polyaspartic cost: what a floor runs in 2026

> Polyaspartic cost runs $8-15 per sq ft installed, or $3,200-6,000 on a 400 sq ft garage. See the line items, the epoxy comparison and where quotes drift.

Canonical: https://epoxygaragefloorlab.com/polyaspartic-cost/

Last updated: 2026-11-09

A polyaspartic garage floor costs $8 to $15 per square foot installed, which puts a 400 sq ft two-car garage at $3,200 to $6,000. The resin is not the expensive part: grinding, crack repair, a base coat and the crew's time make up most of the total, and the polyaspartic is the last layer applied. That ordering explains why two quotes for the same square footage can differ by thousands of dollars without either one being dishonest.

## What the rate per square foot covers

A polyaspartic system is a multi-layer floor in which an aliphatic polyurea topcoat is applied over a prepared slab, usually over an epoxy base coat that carries the color and the flake.

The $8 to $15 band prices that whole sequence, not a single coat:

- Diamond grinding, at $1 to $3 per sq ft
- Crack and spall repair, priced per repair
- Moisture mitigation, at $2 to $5 per sq ft, only if the slab fails a test
- Primer and an epoxy base coat
- Vinyl flake broadcast, if the design calls for it
- Polyaspartic topcoat, one or two passes

A quote that lists polyaspartic as the material and nothing else is quoting a recoat, not a floor. Ask which of the six items above are inside the number before you compare it to another bid.

## Cost by garage size

| Garage | Area | Polyaspartic system | Professional epoxy |
| --- | --- | --- | --- |
| Single | 250 sq ft | $2,000-3,750 | $1,250-3,000 |
| Double | 400 sq ft | $3,200-6,000 | $2,000-4,800 |
| Triple | 600 sq ft | $4,800-9,000 | $3,000-7,200 |

The arithmetic is multiplication at both ends of the band: 250 × $8 = $2,000 and 250 × $15 = $3,750; 400 × $8 = $3,200 and 400 × $15 = $6,000; 600 × $8 = $4,800 and 600 × $15 = $9,000.

Per-square-foot prices fall as the floor gets larger because setup, travel and mobilization are fixed. A crew that spends half a day grinding a 250 sq ft slab spreads that half day over fewer square feet, so the small floor prices toward $15 while the triple lands closer to $8.

## Where the money actually goes

Take a 400 sq ft job at the middle of the band, $11.50 per square foot. The total is 400 × $11.50 = $4,600, and it splits roughly like this:

| Line item | Basis | Approximate share |
| --- | --- | --- |
| Grinding and prep | $1-3 / sq ft | $400-1,200 |
| Crack and spall repair | Per repair | $0-400 |
| Epoxy base and flake | Materials plus labor | $1,200-2,000 |
| Polyaspartic topcoat | Materials plus labor | $700-1,400 |
| Mobilization and cleanup | Fixed | $200-600 |

Those figures are an estimate of how a typical bid distributes, not a published cost breakdown, and the split moves with slab condition. The point is that the polyaspartic layer is the smallest of the big line items. Removing it from a spec saves less than homeowners expect, and adding it to a cheap epoxy job does not fix prep that was skipped.

## Polyaspartic vs epoxy, in dollars

| System | Rate | 400 sq ft | Gap vs epoxy |
| --- | --- | --- | --- |
| DIY epoxy kit | $3-7 | $1,200-2,800 | Not comparable |
| Professional epoxy | $5-12 | $2,000-4,800 | Baseline |
| Polyaspartic system | $8-15 | $3,200-6,000 | +$1,200 |
| Metallic epoxy | $10-20 | $4,000-8,000 | +$2,000 |

Subtract the rows rather than reading the headlines. Polyaspartic at $8 to $15 against epoxy at $5 to $12 leaves $3 per square foot at both ends of the range, and 400 × $3 = $1,200 on a two-car garage. On 600 sq ft the same gap is 600 × $3 = $1,800.

What that $1,200 buys is UV stability, a faster return to service and better abrasion resistance. What it does not buy is a fix for a wet slab. Moisture mitigation at $2 to $5 per square foot adds $800 to $2,000 on 400 sq ft and applies to either system equally.

## What pushes a quote to the top of the range

**Old coating removal.** Grinding off a failed paint or epoxy layer can double prep time, and prep is the labor line.

**Slab damage.** Spalled sections and structural cracks need concrete repair before any coating, and that is a separate trade with a separate invoice.

**Access.** A garage packed with shelving, a water heater in the corner and a step into the house takes longer to mask and coat than an empty rectangle.

**Flake and custom color.** A full flake broadcast to rejection plus a clear topcoat adds material and time. Metallic at $10 to $20 per square foot is a different product entirely.

**Short notice and winter work.** A crew that has to fit you in this week, or work in a cold garage with heaters, prices the inconvenience.

## Five steps to price your own floor

1. **Measure the actual coated area.** Include the apron, closets and the 4-inch stem wall, then add 10% for waste and cuts.
2. **Test the slab for moisture.** A plastic sheet taped down for 24 hours is the cheap version; a calcium chloride test is the documented one. A failure adds $2 to $5 per square foot.
3. **Photograph every defect.** Cracks, oil stains, spalling and old coating become the change-order list, and the list belongs in the bid.
4. **Ask for the same five-line quote from three crews.** Prep, repair, base, topcoat and cleanup, each with a price and a square footage.
5. **Book around the cure.** Polyaspartic returns a floor to vehicle traffic in about a day, but the slab still has to be empty and the weather still has to cooperate.

## When the premium does not pay

A shaded garage on a dry slab with a week of downtime available does not need the fast, UV-stable topcoat, and a well-built epoxy system at $5 to $12 per square foot will give years of service for $1,200 less on a two-car floor.

The premium pays when the door faces south or west, when the floor takes road salt from a daily driver, or when the garage cannot be out of service for a week. In those cases, the $3 per square foot is buying a property the cheaper system does not have.

For the layer-by-layer sequence, read [polyaspartic installation](https://epoxygaragefloorlab.com/polyaspartic-installation/). If you are still choosing a system, [polyaspartic vs epoxy](https://epoxygaragefloorlab.com/polyaspartic-vs-epoxy/) compares them attribute by attribute, and [epoxy garage floor cost](https://epoxygaragefloorlab.com/epoxy-garage-floor-cost/) builds the same budget for the cheaper route. [Garage floor coating cost](https://epoxygaragefloorlab.com/garage-floor-coating-cost/) puts both next to polyurethane and paint.